The AMZCHEF 1050 CFM Range Hood is a 30 inch, ducted only under cabinet hood whose dual blower carries a claimed 1050 CFM without HVI certification. Its strength is airflow headroom over a gas range. Its catch is no sone rating and conflicting dimensions across variants. It suits a gas kitchen that already vents outside.
Airflow headroom is the reason to look, since a claimed 1050 CFM clears what a typical 30 inch gas range needs by a wide margin. It pairs a dual blower with dishwasher safe baffle filters. In our assessment, the weak point is the spec sheet rather than the motor, with no sone rating, no HVI certification, and no consistent dimensions. For anyone planning a ducted install, that means measuring before ordering.
Who It’s For: Gas Cooks With a Duct
This AMZCHEF hood suits a 30 inch gas range used daily for searing or wok cooking, in a kitchen with an exterior duct already in place. It gives you far more than the 400 to 650 CFM that range calls for, at an entry tier outlay. If your range is 36 inches wide, we would steer you toward the 36 inch version of the same hood.
Skip it if you rent, cannot vent outside, or cook in an open plan room where noise matters. It cannot run ductless and comes with no noise rating.
What We Liked
What Could Be Better
AMZCHEF 1050 CFM Specs at a Glance
Specification | Detail |
Airflow Ratings | 1050 CFM |
Sone rating | Not stated |
Speed settings | 3 |
Filter type and count | Stainless steel baffle, dishwasher safe |
Mounting height range | Not published |
Lighting | LED |
Controls | Push button, or touch with remote, gesture, and timer (by variant) |
Convertible to ductless | No, ducted only |
Warranty | Up to 2 years limited |
Read Also: Our Top 10 Under Cabinet Range Hood Recommendations
Airflow and Noise
A claimed 1050 CFM covers about 105,000 BTU of gas burner output at the usual 1 CFM per 100 BTU. A typical 30 inch gas range totals 40,000 to 65,000 BTU, which calls for roughly 400 to 650 CFM. Sized by room volume instead, 15 air changes an hour in a 12 by 14 foot kitchen with 8 foot ceilings (1,344 cubic feet) works out to about 340 CFM.
That 1050 figure is a claimed rating without HVI certification, and it rates the blower rather than your duct cap. The standard we hold this class to assumes a 20 to 30 percent loss through 10 to 15 feet of duct with two elbows, which puts delivered output near 735 to 840 CFM. We read AMZCHEF headline figures with care, since the 750 CFM sibling is rated at just 700 CFM in its own technical details.
The hood carries no sone rating for any of its three speeds, and no decibel figure either. About 1 sone matches a refrigerator hum and 3 to 4 sones matches normal conversation, so the low setting is the one that decides daily comfort. Whether that setting is quiet enough and strong enough for everyday cooking is a question its specs leave open.
Fit and Install: Measure Before You Order
Nominal width is the only dimension you can rely on, at 30 inches. The stainless variants carry a stated 22.1 inch width and the black variant carries the 36 inch model’s 35.2 inches, so we flag depth and height as unconfirmed until a dimensioned drawing is available. Over a 30 inch gas range, the 36 inch version catches more of the plume where your cabinets allow it.
The hood has three outlet positions in round and rectangular shapes. Its round collar appears to measure near 5.9 inches (150 mm), so check that it seats on your 6 inch duct before buying fittings. The hood also comes without a stated mounting height, cabinet depth, or electrical connection.
At 1050 CFM, the hood sits well above the 400 CFM make up air threshold in the IRC, so confirm requirements with your local building authority.
Filters and Build: Easy Care, Short Track Record
The stainless steel baffle filters are dishwasher safe, and a monthly cycle keeps them clear at moderate cooking frequency, with no charcoal filter cost. The body is 430 stainless steel (gauge not stated), and gesture control on the touch version keeps greasy fingers off the panel.
Our take on support is mixed. The hood is backed by a US support line and a brand that also makes 700 to 750 CFM under cabinet hoods, but it is missing from AMZCHEF’s own site. Its LEDs have no stated replaceability, though wide availability across major retailers lowers the risk of it going unsupported.
Our Scores: Big Airflow, Little Proof
In this AMZCHEF 1050 CFM review, we score the hood against daily, high heat cooking over a 30 inch gas range, which is the use our scoring weighs most.
Dimension | Rating |
Airflow performance | 3/5 |
Noise level | 3/5 |
Build quality | 3/5 |
Filters and maintenance | 4/5 |
Installation | 3/5 |
Value | 4/5 |
How It Compares: The 750 CFM Sibling Publishes More of Its Numbers
The closest comparable is the AMZCHEF 750 CFM under cabinet hood, with the same touch, remote, and gesture controls. It is rated at 700 CFM and 63 dB and measures 29.8 by 19.69 by 5.98 inches, so you can plan a cabinet fit. We would pick the 750 for a 30 inch electric cooktop or a kitchen where a rated noise figure matters. The 1050 earns its place over a 65,000 BTU gas range on a long duct run, where 700 CFM can drop below the 650 CFM that range needs.
FAQs
Is 1050 CFM too much for a 30 inch gas range?
No, provided your duct and make up air can support it. A typical 30 inch gas range needs 400 to 650 CFM, and the headroom offsets duct losses. We suggest confirming local make up air rules first.
Can the AMZCHEF 1050 CFM under cabinet range hood run ductless?
No. It is ducted only, and no charcoal filter kit is available, so it does not suit a kitchen that cannot vent outside.
What duct size does this hood need?
The hood has no stated duct size. It has round and rectangular outlets, so measure the round collar against your 6 inch duct before buying a transition.
Our Verdict
After a full evaluation, our position is clear on the AMZCHEF 1050 CFM Range Hood. Buy it if you cook hard over a 30 inch gas range, already vent outside, and can plan for make up air, because its claimed airflow sits well above that range’s needs. Avoid it if you need ductless operation, a noise level you can verify before purchase, or dimensions you can trust without measuring the delivered unit.
Measure your collar and cabinet first, and you will know quickly whether this hood belongs in your kitchen.